2/26/2024 0 Comments Panet waves mandolin tunerThe unique pick-sized Planet Waves SOS Strobe Tuner uses Planet Wave's revolutionary Strobe-On-String technology. If/when this unit fails I will not hesitate to buy another.These are come old/new stock tuners we had tucked in a drawer. The response time is fast (even in the loose condition I described above) and it is at least as accurate as other piezo tuners in my experience based on matching readouts. My experience with this piece of gear has been positive, and I suspect it would mount as intended on a 24 bracket instrument without issues. The original battery is still powering my tuner. It is unobtrusive and not in the way when my banjo is placed into it's Access gig bag. ![]() ![]() Perhaps the feature I find most attractive about the NS Micro is that I can and do leave it on my instrument permanently. Readings from the NS Micro tuner match those of two different Snarks that mount on the headstock. I like having the tuner at the pot, directly in my line of vision simply by glancing downward. It rattles a bit when I move the instrument, but I have not noticed any issue with this while playing, and, as I mentioned above, the tuning capability appears not to be adversely influenced. I was initially concerned about this arrangement, but there have been no dysfunctions of the electronics or accidental uncoupling of the assembly from my instrument. Instead, the plastic strips sit beneath two brackets and the assembly is loose, albeit not in danger of falling off the pot. My Pisgah Woodchuck is an 18 bracket instrument and the brackets are far enough apart that the tuner does not mount as I've described. The tuner's mounting strips are supposed to lay beneath brackets 1 and 3 and there is an indentation in the mounting system that is designed to fit over bracket number 2 in the series of three, thereby stabilizing the entire assembly. Consider a set of three brackets, which I'll refer to as 1, 2, and 3. The tuner is designed to mount via plastic strips that are supposed to span the distance of three brackets. I've had the tuner on my banjo constantly for about six weeks now and I find it quite satisfactory. It's been a while since I asked about the Planet Waves PW-CT-16 NS Micro Banjo Tuner, and I mentioned at the time that I would post a review after I had used it for a while. I'm also using the same tuner with the headstock mount for my mandolins, and my wife is using the same for her guitars. I've purchased the same tuner and made the same mount for each of my main-playing banjos. To change the battery, I simply slide the tuner forward which releases the back side of the mount from under the hook for removal. The mount I made is a simple keyed strip made of a fairly stiff piece of ~1/24" black polycarb sheeting sandwiched around mylar. I like the display and the size and shape of the tuner, but I didn't like the original mount because it was too exposed and in the way for my tastes - I keep my picks in the same area and every time I went to get them the mount would move. I almost always tune with harmonics instead. All small tuners tend to pick up overtones with a banjo especially if the instrument is tuned using open strings. But I've made a different mount for it (see below). ![]() ![]() Meantime, I wonder if anyone has direct experience with this tuner and your thoughts if so? I'm keen on trying one out (it's a cheap thrill at $16ish) and will post a review if anyone is interested. Even if not, it appears the strap mounted tuner can be left on the instrument when it's put back in a case or maybe even a gig bag. Regardless, I wonder whether the strap mount at the pot will be helpful in terms of overall sensitivity to the fundamental of any given string. Damping strings other than the one being tuned generally helps eliminate the overtones which I assume are tricking the tuner. Strings seem to tune to pitch despite this and I've gotten used to the phenomenon. A headstock-mounted Snark works ok, but I frequently get readings of the 4th harmonic note rather than the fundamental. The banjo-specificity is a function of the actual tuner component being mounted to a strap that appears in pictures to mount at the pot beneath the bracket hooks. I happened to see this banjo-specific tuner and have ordered one.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |